- KMT Waterjet
STREAMLINE PRO® Pumps
With the introduction of the Ultra High Pressure (UHP) KMT STREAMLINE PRO® series of 90,000 PSI waterjet pumps, KMT Waterjet Systems has the broadest line of abrasive waterjet intensifier pumps available. The PRO has three horsepower options for various cutting applications: 50 hp, 60 hp, and 125 hp. The world’s fastest water jet!
KMT Waterjet
STREAMLINE PRO® Series
- 90000 PSI | 125 HP Pumps
World's fastest waterjet
The PRO 125 HP pump doubles the power of the abrasive waterjet table by cutting product in half the time compared to traditional 60,000 PSI | 100 HP waterjet systems.
Technical Parameters
- Motor Rating
125hp (93.2kw)
- Pressure Range (Deadhead)
90,000psi (6.200 bar)
- Max. Flow Rate at Max. Pressure (60 Hz)
1.59 gal/min (6.0 lpm)
- Length
88” (2,230 mm)
- Width
59.09” (1,500 mm)
- Height
61.12” (1,552 mm)
- Attenuator Volume
.42 gal (1.6 L)
- Cutting Water Inlet Pressure
35-85psi (2.41-5.86 bar)
- Min. Cutting Water Inlet Flow
8 gal (30 L)
- Low Pressure Filter
10 µm abs.
- Nom. Current at 480V/60Hz (Full Load Amp)
70 A
- Hydraulic Tank Capacity
110 gal (416 L)
- Oil Level and Temperature Control
Sensor
- 90000 PSI | 60 HP Pumps
Reduce the cost per part
The PRO 60 HP pump will provide a dramatic 50 – 70% increase in cutting speed over the industry standard 60,000psi (4,137 bar)/50hp cutting speed.
Technical Parameters
- Motor Rating
60hp (45kw)
- Pressure Range (Deadhead)
90,000psi (6.200 bar)
- Max. Flow Rate at Max. Pressure (60 Hz)
0.78 gal/min (2.9 lpm)
- Length
83.7” (2,126 mm)
- Width
53.7” (1,364 mm)
- Height
59.3” (1,506 mm)
- Attenuator Volume
.42 gal (1.6 L)
- Cutting Water Inlet Pressure
35-85psi (2.41-5.86 bar)
- Min. Cutting Water Inlet Flow
4.0 gal (15.1 L)
- Low Pressure Filter
10 µm abs.
- Nom. Current at 480V/60Hz (Full Load Amp)
70 A
- Hydraulic Tank Capacity
55.8 gal (211 L)
- Oil Level and Temperature Control
Sensor
- PRO 50 HP Pumps
Lowest Cost Per Part
Compared to the industry standard 60,000 psi (4,137 bar)/50 hp cutting speed, PRO 50 hp pumps can dramatically increase cutting efficiency by up to 40%.
Technical Parameters
- Motor Rating
50 HP | 37 kW
- Pressure Range
15,000 - 90,000 PSI | 1.000 - 6.200 bar
- Max. Flow Rate
0.64 gal/min| 2,4 l/min
- Max. Orifice @ Max. Pressure
.010" | 0,25mm
- Dimensions (mm)
1311 x 1163 x 1575
- Weight
2,888 lbs. | 1310 kg
- Accumulator Volume
0.26 Gallon | 1 Liter
- Min. Cutting Water Inlet Pressure
45 PSI | 3 bar
- Min. Cutting Water Inlet Flow Rate
2 Gallon | 7,6 Liter
- Cooling Mode
Oil/Water
- Cooling Water Pressure
35-100 PSI | 2,4 - 2,9 bar
- Label According to EC-Machinery Directive
CE mark & CE Declaration of Conformity
- Max. Noise Level